Blog ·
How much electricity does an LED wall really use?

Less than most people expect. An LED wall almost never runs at its full rated power, because real content is rarely a full-white screen. For planning, average use is about one third of the peak figure on the datasheet. A 10 ft × 6 ft indoor wall running 10 hours a day typically adds around 300 units a month to your EB bill.
Here is how to work it out for your own screen, and what to plan on the electrical side.
Peak power and average power are two different numbers
Peak power is the screen showing full white at full brightness, with every LED lit. It is the number your electrician uses to size the cable, MCB and supply, because the screen must be able to handle it safely.
Average power is what the screen actually draws while playing normal videos, images and text. Dark backgrounds, moving pictures and lower brightness settings all pull it down. This is the number that decides your monthly bill.
| 10 ft × 6 ft indoor LED wall (60 sq.ft) | Planning figure | Used for |
| Peak power | About 3.1 kW | Cable, MCB and supply sizing |
| Average power | About 1.0 kW | Monthly units and EB bill |
Figures from our power calculator, which plans indoor walls at 550 W per m² peak. Actual draw depends on the model, brightness setting and content.
A Tamil Nadu EB bill example
Take the same 10 ft × 6 ft indoor wall in a showroom in Coimbatore, switched on from 10 am to 8 pm.
Average power: about 1.0 kW
Hours per day: 10, so about 10 units a day
Days per month: 30, so about 300 units a month
Tariff: commercial tariffs are often ₹8 to ₹10 a unit. At ₹9 a unit, that is about ₹2,700 a month.
Your actual rate depends on your tariff category and slab, so check your own EB bill and use that figure.
Now an outdoor example: a 10 ft × 5 ft hoarding on a building front, on for 12 hours a day. Outdoor screens run much brighter, so they draw more. Peak is about 3.7 kW and average about 1.4 kW, which works out to around 510 units, or roughly ₹4,600 a month at ₹9 a unit.
Try it yourself: enter your screen size, hours and tariff in our free LED power and electricity cost calculator. It shows peak and average power, monthly units, the EB cost, and the MCB size and supply type you need.
Indoor and outdoor screens use power very differently
Brightness is the biggest driver of power. Indoor screens are set much dimmer because they are viewed up close under shop lighting. Outdoor screens have to stay readable in direct sunlight, so they run several times brighter and draw more power per square foot.
| Screen type | Typical brightness | Peak, per sq.ft | Average, per sq.ft |
| Indoor LED wall | 600 – 1,000 nits | About 51 W | About 17 W |
| Outdoor LED screen | 4,500 – 6,500 nits | About 74 W | About 28 W |
Planning figures used in our calculator (550 and 800 W per m² peak). Use the datasheet of the exact model for the final electrical design.
See fine-pitch options on our indoor LED display page, or weather-rated screens for shop fronts and hoardings on our outdoor LED display page.
What to plan on the electrical side
Single or 3-phase: a single-phase 230 V supply is usually enough for screens up to about 5 kW peak. Bigger screens need a 3-phase 415 V supply, with the cabinets spread evenly across the phases.
Dedicated MCB: give the screen its own MCB and cable, sized on peak power with some headroom, not on average power.
Stabilizer: where the voltage fluctuates, add a stabilizer with about 20% spare capacity over the screen's peak load.
Outdoor screens: plan a separate earth pit, surge protection (SPD) and an outdoor-rated distribution box.
Indoor heat: a screen gives off its running power as heat. In a closed room, a 1 kW average load adds roughly 0.3 TR to your AC load.
Quick checklist to keep the bill low
Schedule the screen to switch off when the shop is closed.
Lower brightness in the evening, using a brightness schedule or a light sensor where the controller supports it.
Prefer darker backgrounds in your content; full-white slides draw the most power.
Size the screen for the viewing distance, not bigger than you need. The size calculator helps.
Use your own EB tariff in the power calculator before you budget.
Frequently asked questions
Will an LED wall trip my shop's breaker?
Not if it is wired correctly. The screen should have its own MCB and cable sized for its peak load. Larger screens may need a load extension or a 3-phase supply, which we check during the site survey.
Does the screen use full power all the time?
No. Full power is only reached on a full-white screen at maximum brightness. Normal content averages about a third of peak indoors.
Do I need a 3-phase connection?
Only for large screens. As a rough guide, screens above about 5 kW peak should go on 3-phase. The power calculator tells you which one your screen needs.
How can I reduce the electricity cost?
Switch the screen off after business hours, dim it in the evening, and avoid full-white content. These three steps make the biggest difference.
Will you help with the electrical plan?
Yes. During the site survey we check your supply and load, and tell you the MCB, cable and stabilizer you need before you order.
Planning a screen? Get the numbers first
Tell us the screen size, location and daily hours, and we will share the power load and electrical requirements along with the quote. We reply within one working day, and our own technicians handle mounting, wiring and commissioning across Tamil Nadu, Kerala and Puducherry. Ask for a quote below.
Phone: 94038 90883 · Email: sales@manyuinternational.com · WhatsApp: +91 74068 35576
